EcoFlow DELTA Pro 3 Portable Power Station + Smart Home Panel 2

Yes, EcoFlow DELTA Pro 3 can be connected to EcoFlow Smart Home Panel 2 through the power input/output port.

Yes, EcoFlow DELTA Pro 3 can be connected to the EcoFlow 50 Amp Hub dedicated for EcoFlow DELTA Pro Ultra via the AC Power IN/OUT port, supporting the parallel connection of up to 2 sets of EcoFlow DELTA Pro 3.

EcoFlow DELTA Pro 3 has two PV input ports, which are for high-voltage PV port and low-voltage PV, respectively.High-voltage PV: 30-150V, 15A Max, 1600W Max. Low-voltage PV: 11-60V, 20A Max, 1000W Max.

When the device is powered off, press and hold the power button for more than 5 seconds. The device's LCD screen will light up, and then the screen will blink once (it must blink once), indicating that the Bluetooth connection has been successfully reset.

Yes, it supports Level 1/2 EV chargers. You will need to purchase a dedicated EcoFlow adapter, the EV X-Stream Adapter (DELTA Pro Ultra). Typyically, the grid charging port on the US model only supports AC 120V 2000W charging (Level 1). However, by using the AC POWER IN/OUT port along with the EV X-Stream Adapter (DELTA Pro Ultra), you can connect a 240V EV charger, increasing the charging rate to 4000W (Level 2).

No, but it can perform split-phase output as a standalone unit.There are two buttons for AC output: 120V AC ON/OFF and 240V AC ON/OFF.1. When the 120V AC button is pressed, four 120V 20A outlets and one 30A RV outlet will supply power, and the 240V outlet will be turned off.2. When the 240V AC button is pressed, one L14-30 split-phase outlet and one 6-20R 240V outlet output power, and the 120V outlet will be turned off.

Yes, it will.However, there are specific requirements for the light conditions. In weak lighting environments, it might not trigger the device to power on.

EcoFlow 800W Alternator Charger

EcoFlow Smart Home Panel 2

EcoFlow Smart Generator (Dual Fuel)

EcoFlow DELTA Pro to Smart Generator Adapter

EcoFlow PowerInsight Home Energy Manager

EcoFlow WAVE 2

EcoFlow Smart Generator 4000 (Dual Fuel)

Please note that all devices need to be upgraded to the latest firmware version to ensure compatibility.

EcoFlow DELTA Pro Smart Extra Battery

EcoFlow 50 Amp Hub (DELTA Pro Ultra)

EcoFlow EV X-Stream Adapter (DELTA Pro Ultra)

EcoFlow DELTA Pro Remote Control

Please note that all devices need to be upgraded to the latest firmware version to ensure compatibility.

4000 cycles.After undergoing 4000 cycles at a rate of 0.5C/0.5C at 25°C (77°F), the battery maintains over 80% of its state of health (SoH).

Optimal operating temperature: 20°C-30°CCharging temperature range: 0℃-45℃Discharge temperature range: –10℃-45℃Recommended long-term storage temperature: 20℃-30℃

As the core component of the device, the safety and protection level of the battery pack is crucial. To better protect the battery pack and reduce the risk of short circuits and fires caused by water ingress, the EcoFlow DELTA Pro 3 battery pack is sealed. It has reached an IP65 waterproof and dustproof rating, effectively preventing dust from entering and resisting water spray.However, the EcoFlow DELTA Pro 3 main unit does not have a waterproof and dustproof rating (IP20). The device is suitable for use in well-ventilated indoor environments or sheltered outdoor environments to avoid the impact of rain and dust on the device. Please ensure that the surrounding environment is dry and clean during installation and use to ensure the device's normal operation and longevity.

EcoFlow DELTA Pro 3 is equipped with an internal GFCI ground circuit. Users can connect an external GFCI protector according to their needs. When an external GFCI protector is connected to EcoFlow DELTA Pro 3, the GFCI support switch must be turned on in the app for the external GFCI protector to function properly.

No, not supported.

Yes, supported. Please note that all devices need to be upgraded to the latest firmware version to ensure compatibility.

No, not supported.

Supported. However, due to the different capacities of the EcoFlow DELTA Pro Extra Battery and the EcoFlow DELTA Pro 3 Extra Battery, there will be some SOC imbalance.

No, not supported.

It's normal. EcoFlow Smart Home Panel 2 uses internal switches (relays) to control branch circuits on/off and the power input/output port of the battery connection box. When the mode is switched or you press the emergency stop button, you may hear a series of "click" sounds because of internal switches.

The physical breaker in the panel has been tripped.

Please contact an electrician or customer service to install or replace the circuit breaker and turn it on in the app to support up to 12 circuits.

No.

Under normal circumstances, the TOU mode efficiently utilizes solar energy to prevent waste. Here's how it works: When solar energy is available, the TOU mode intelligently allocates the portions of the battery capacity to be charged from solar and the grid ahead of time. If plenty of solar energy is expected for the day, the grid won't be used to charge the battery unless the actual solar generation falls short. However, in cases where there's excess solar energy and the battery is already fully charged, some of that solar energy may go unused if the solar output doesn't meet the load power requirement.

Here are a few reasons why your TOU schedule isn't executing: a. The battery has reached its charge limit. b. The battery level has dropped below the backup reserve level. c. Storm Guard has been activated due to severe weather conditions.

The serial number QR code can be found on the nameplate located on the back of the glass door. Scan the code to get your S/N number.